MMX200
A streamlined model free of parts projecting outside the frame.
| MMX200 | VG | SD2 | CF | 1 | 03 | 200 | 150 | IV-12.5 | A | SP | RE1 | |
| Model | Type | Motor drive type | Special design type | Power supply | Output | Belt width (mm) | Product length (cm) | Speed symbol | Motor symbol | Aditional function (option) | ||
| Speed type | Speed no. | Food-use compatibility | Tail shape | |||||||||
| MMX200 | [Blank] Standard |
[Blank] Standard SD2 Small motor drive SDH Small motor drive, hollow-shaft motor CDU Motor top mount |
[Blank] Standard CF Horizontal top VT V-trough |
1: Single-phase 100 V 2: Single-phase 200 V 3: Three-phase 200 V |
03: 25 W 04: 40 W Restricted by special design type. |
50, 75, 100 150, 200, 250 300, 400, 500 Restricted by type and specification. |
25~600 Restricted by type and specification. |
K: Constant speed U: Speed-controller variable speed IV: Speed-controller inverter variable speed IVH: General-purpose inverter variable speed DC: DC motor variable speed |
12.5, 15, 18, 25, 30, 36, 50, 60, 75, 90, 100, 120, 150, 180 SD2 and CDU and CDU motor drive types: 7.5, 9, 12.5, 15, 18, 25, 30, 36, 50, 60, 75, 90, 100, 120 |
A Sumimoto O Oriental M Panasonic Sdh and DC motor variable-speed motor drive types: "O" motor only |
SP | Roller edge (ultra-low diameter rollers) RE1: Output side RE2: Intake side RE3: Both sides Belt detensioner BL1: Output side BL2: Intake side BL3: Both sides FS: Increased safety Restricted by type and specification. |
| VG No lateral belt drift |
75, 100, 150, 200, 250, 300, 400, 500 Restricted by type and specification. |
SP (Belt width of 300 mm max.) |
||||||||||
Note :
- When no symbol applies or no appended symbol is needed, the symbol and the hyphen (-) before it are omitted.
- The model designations shown here are for the purpose of illustrating the symbols, and in some cases may denote models that do not actually exist.
- See the options page for information on the belt detensioner.
SPECIFICATION
| Motor output | 25 W, 40 W | |||||||||
| Belt width (mm) | Standard | 50 | 75 | 100 | 150 | 200 | 250 | 300 | 400 | 500 |
| VG | - | 75 | 100 | 150 | 200 | 250 | 300 | 400 | 500 | |
| Product width (mm) | 95 | 120 | 145 | 195 | 245 | 295 | 345 | 445 | 545 | |
| Product length (cm) | Standard | 50, 100, 150, 200, 250, 300, 350, 400, 450, 500, 600 | ||||||||
| VG | ||||||||||
| Belt | Polyurethane, green | |||||||||
| Minimum product height (mm) | 160 (motor drive unit) | |||||||||
Note :
- Choose a 40 W motor when exceeding a product length of 400 cm.
- Use 50% of the value for the standard type as the guideline value for the VG type's conveyor payload.
Standard/VG model belt lengths
| Product length of 300 cm max. | Product length x2+235 |
| Product length of 300 < L ≤ 600 cm. | Product length x2+225 |
Conveyor payloads
Use 50% of the value for the standard type as the guideline value for the VG type's ,CF type's,VT type's conveyor payload.
MMX200 Standard Power supplies and speeds
Note:
- Actual speeds may vary by up to 10% less than the values shown, depending on the motor characteristics and payload.
- Speeds of DC motor variable speed models may vary by up to 0.6% more or less than the values shown, depending on the motor characteristics and payload.
- Variable-speed models should only be used within the specified speed range since low-speed operation may cause motor burnout.
- Use slow speeds (K, U, IV-18 or less) for 25 W motors.
- For product lengths of over 400 cm, select a 40 W motor, and use a speed symbol of 25 or less for the U and IV types.